Про paypal ни скажу, ни знаю, но я покупал при помощи обычной виртуальной интернет карточки, которую мне оформили через сайт моего банка. Правда я купил программу, потому что файлы делаю сам.

Я тут заметил следующее, если режешь по меткам. то делаешь автоматический их найти, так вот после этого ненужно проверять как нож прорежет бумагу, иначе плоттер теряем метки и после этого нужно по новой метки искать, может из за этого у вас и смещается, было тоже самое.

Thank for sending over these files. We have cut the file on our end and the cut went through successfully. Here are some troubleshooting steps to go over to help your cut also cut successfully.
If the image being cut is not lining up properly where the start and end points of the cut line are not matching up, or the image appears to be skewed and mis-aligned during the cutting process, please explore the following points:
The cutting mat (or material if no mat is in use) is drifting/moving off the rollers

• Ensure the cutting mat is being used for materials that do not have their own adhesive backing. If using paper or cardstock (or another material type that does not have a pre-adhered backing), load the material onto the cutting mat. Part of the cutting mat's purpose is to hold the material in place to ensure the resulting cut can be aligned properly.
  
• Ensure the mat or material is being loaded properly. If the material or cutting mat is not lined up correctly with the intended guide mark and is not being initially grabbed between the two white rollers, the material will drift as it is being cut and the image would not be aligned properly. Visit http://www.silhouetteamerica.com/faq/solution/196 for further information on proper loading techniques.
  

The material is on a cutting mat and appears to be drifting/moving around on the mat (even though the mat itself is securely in place)

• Check the mat to see if the adhesive has worn down. If the mat has lost its adhesive quality (either overall or in select areas of the mat) and is not holding the material firmly in place during the cutting process, the cutting mat will need to be replaced.
  
• Check to see if the concern is specific to the material type by testing an alternate material. Some specialty materials (especially those which may be thicker) may experience concerns in how they are being gripped by the rollers. As material thickness increases, the rollers (dependent upon the material type and surface) may not grip as firmly on the media's surface during operation. Visit http://www.silhouetteamerica.com/faq/solution/357 for further information on resolving this concern.
  

The material and cutting mat both appear to be gripped properly but the resulting cut is simply not aligning properly

• Ensure the proper loading option is being used to load the material and/or mat as directed at http://www.silhouetteamerica.com/faq/solution/212.
  
• Ensure the blade setting is correct for the material type in use. You may want to perform a series of test cuts (as directed at http://www.silhouetteamerica.com/faq/solution/325) to find the lowest blade setting possible that still successfully cuts your material type. If the blade is at a higher level than necessary, it is possible that the blade is cutting through the material but getting caught on the mat during the cutting process.
  
• Ensure the blade is free from any obstruction and swiveling properly as directed at http://www.silhouetteamerica.com/faq/solution/161.
  
• Check the edges of the cutting mat. If an older mat is in use where the edges are curling upward, this may catch on the motor as it travels along near the edge of the mat and throw of the cutting alignment. If such is the case, the mat will need to be replaced as the edges become compacted and warped over time.
  
• Go to the File menu (PC) or the Silhouette Studio menu (Mac) and go to the Preferences option. Go to the Advanced section and adjust the Packet Size setting to "500 bytes". Then click on OK. This will adjust how information is being sent from the computer to the Silhouette and may resolve select concerns that can arise from a potential communication issue.
  

We hope this information is helpful. Please let us know if you have any questions or concerns after reviewing this information.

Всем добрый день! Возник вопрос, когда я хочу текст нарисовать с помощью ручки, то на бумаге остаются следы от нее (текст как бы исполосован ) , печатала на скорости 3, толщина 5. Можете посоветовать, как сделать, что бы было аккуратно и не было полос от ручки ?

Dol4i

Dol4i

texxnik,  а программа мне потом не скажет, что это куплено не у нас и код не примет?:)

как что-нибудь стереть в программе Студио?

Здравствуйте, столкнулся с такой проблемой - в кореле создаю документ А4 на него выкладываю jpg картинки, сохраняю в dxf формате, в silhouette открываю - пустое поле, рисунков нет, и даже размеченного листа А4 тоже нет. 

Всем привет, с прошедшими праздниками. У меня вопрос  по сохранению узоров, не могу сохранить узор, то есть перетаскиваю в папку а мне показывает значок запрета. В чем может быть дело?

Всем привет, с прошедшими праздниками.
У меня вопрос  по сохранению узоров, не могу сохранить узор, то есть перетаскиваю в папку а мне показывает значок запрета. В чем может быть дело?